GymTagOps.

What is lockout tagout for gym equipment?

Lockout tagout for gym equipment means cutting and locking off a machine's power and stored energy before anyone services it, then tagging who did it.

Nookesh Karri · · 8 min read

Cover card with the title: What is lockout tagout for gym equipment?

Lockout tagout for gym equipment is the routine that stops a machine starting up, or releasing stored energy, while someone is working on it. You switch the machine off, cut it from its power source, put a lock (lockout) or a warning tag (tagout) on that source, release any stored energy, and check it won’t start. Only then does anyone reach inside the hood or under the belt.

What lockout tagout means in a gym

Lockout tagout (LOTO) is a set of steps for controlling hazardous energy during servicing and maintenance. In the US, the rule is OSHA’s control of hazardous energy standard, 29 CFR 1910.147. It covers servicing where “unexpected energization or start up of the machines or equipment, or release of stored energy could cause injury”.

On a gym floor that means work like:

  • Pulling the motor hood off a treadmill to check the drive belt.
  • Changing a frayed cable on a selectorized machine.
  • Fixing the console wiring on a bike or cross-trainer.
  • Servicing pool pumps, saunas or HVAC kit, if your team does that.

The OSHA overview of hazardous energy lists the sources as electrical, mechanical, hydraulic, pneumatic, chemical, thermal or other energy. It also notes that people who service equipment routinely face the greatest risk of injury. In a small gym, that is usually the owner or the one staff member who is “good with tools”.

Lockout vs tagout: which one does the standard prefer?

The standard prefers lockout. A lockout device uses a positive means, such as a lock, to hold the switch or valve in a safe position. A tagout device is a prominent warning tag fixed to that switch. Under section (c)(2), if the isolating device can take a lock, you use a lock, unless you can show a tag gives the same protection. Tags are for devices that can’t be locked.

A lock stops the switch moving. A tag only asks people not to move it, and someone has to read it first.

How lockout tagout differs from an out of order sign

An out of order sign protects members from a broken machine. Lockout tagout protects the person fixing it. You often need both on the same treadmill, at different times.

When a member reports a fault, you take the machine out of use and sign it. That tag stays on for days. Lockout is shorter and more personal. It goes on when the repair starts, it names the person working, and it comes off when they finish.

The lockout tagout steps for gym equipment

The standard sets out the steps in a fixed order. Here they are applied to a commercial treadmill:

  1. Prepare. Know what powers the machine before you touch it. Is it a plug, a wall switch or a hardwired circuit?
  2. Shut down. Stop the belt and turn the machine off at its own switch.
  3. Isolate. Cut it from the power source: pull the plug, or switch off the disconnect or breaker.
  4. Lock and tag. Put your lock and tag on that disconnect. If it’s a plug, keep the plug with you.
  5. Release stored energy. Let the flywheel and belt stop. Lower anything that is raised.
  6. Verify. Press start. Nothing should happen. Then turn the switch back to off.

When you finish, remove your tools, check the guards are back, tell the staff on shift, and only then take your lock off.

Is unplugging a treadmill enough?

Unplugging is enough only when the treadmill is actually unplugged and the plug stays under your exclusive control. That is the cord and plug exception in section (a)(2)(iii)(A). Most plug-in cardio kit can use it, which makes it the rule gyms lean on most.

OSHA’s 2010 interpretation letter says exclusive control means you are “continuously in a position to prevent” others from plugging it back in. A plug about five feet away may not count. The exception also covers only cord and plug equipment, not machines isolated with a disconnect switch.

In the Tops Markets case, the review commission held that the exemption only applies to machines that are actually unplugged, not ones that could be.

Say your treadmills plug into floor boxes under the deck. You unplug one, then walk to the back office for a part. The plug is now on the floor and anyone can push it back in. Either take the plug with you, or put a plug lockout cover on it.

Hardwired or wall-switched treadmills get a lock on the isolator.

Stored energy on strength machines

Stored energy is the part people forget. The standard says stored or residual energy must be “relieved, disconnected, restrained, and otherwise rendered safe” before work starts.

On strength kit, the risk is mechanical, not electrical:

  • A weight stack that is raised holds energy. Lower it fully and pin it at the bottom before you touch the cable or pulleys. Our weight stack maintenance guide covers the rest of that job.
  • A flywheel on a spin bike or rower keeps turning after you stop pedalling. Wait for it to stop.
  • Gas springs on adjustable seats push back when you take them off.

My take: in a small gym, the weight stack is a bigger LOTO risk than the treadmill motor. An unpinned stack drops on fingers far faster than anyone pushes a plug back in.

Who can remove a lock, and who needs training

Only the person who put a lock or tag on should take it off. Section (e) says each device “shall be removed” by the employee who applied it. The standard allows a separate procedure when that person isn’t available, such as when they have gone home with the key.

Training splits two ways:

  • Authorized employees, who do the servicing, learn to recognize hazardous energy sources and how to isolate them.
  • Affected employees, such as front desk and trainers, learn what a lock means and that they must leave it alone.

Inspect the procedure at least once a year, and write down who did it and when. For the rest of your records, see what records a gym should keep for maintenance.

What about outside technicians?

A service technician from a repair company usually brings their own locks and procedure. You still need to tell them how your machines are powered, and tell your staff not to touch the locks. Our guide on working with a gym equipment repair technician covers what to agree before they arrive.

Limits of this guide

This post explains the US OSHA rule and how it fits gym kit. It is not legal advice. Your state may run its own plan, and the UK and other countries have their own rules. The UK HSE’s maintenance guidance says most maintenance should be done with the power off and machines locked off if power could be switched back on.

Software can’t lock a switch. In GymTagOps you can mark a machine’s issue as in progress and assign it to a teammate, so the floor staff can see who is working on it. Try it in the live demo. The physical lock still has to go on the plug or the isolator.

FAQ

Do gyms need a lockout tagout program?

In the US, a gym whose staff service or maintain machines where unexpected start-up or stored energy could injure them falls under the OSHA standard 1910.147. If your team only unplugs plug-in machines and keeps the plug in hand, the cord and plug exception may cover that work. Outside contractors bring their own procedure, but you still need to coordinate with them.

Is unplugging a treadmill enough for lockout tagout?

Often, yes, if the treadmill is actually unplugged and the person working on it keeps the plug under their exclusive control. If it runs from a hardwired circuit or a disconnect switch, the exception does not apply and you need a lock on the isolating device.

What is the difference between lockout and tagout?

Lockout uses a physical lock to hold the power switch or valve in the off position. Tagout uses a warning tag attached to it. The standard prefers lockout whenever the device can take a lock.

Who can remove a lockout tag on gym equipment?

The person who put it on. The standard allows a special procedure only when that person is not available, so a manager should not simply cut someone else’s lock.

Sources

Keep reading